Start with the two pieces, not the glow
Gino the Bead Invisible Glow is an end-stop lanyard bead, which means its job is to cap the end of your cord rather than slide along it. The design is two pieces: a titanium head that threads into a glow-in-the-dark hat. The hat is the part that hides the end of your lanyard, and it is also the part that glows.
That split matters for upkeep. You are not caring for one solid bead. You are caring for a threaded titanium piece and a glow component that join together, so the connection between them is the first thing to understand before you thread anything.
What the catalog confirms about Gino
- Gino the Bead Invisible Glow: Two-piece end-stop lanyard bead with a titanium head that threads into a glow-in-the-dark hat. The threaded joint is the part you will handle most when attaching or removing the bead.

Gino the Bead Invisible Glow - Gino the Bead Invisible Glow: 1/4" (6.5mm) thru hole. This is the clearance your cord or lanyard material must pass through, so check your cord diameter before ordering.
- Gino the Bead Invisible Glow: 13/16" (21mm) tall and 7/8" (22mm) diameter. These dimensions tell you how much space the bead takes up at the end of a lanyard and how it will sit in hand or pocket.
- Gino the Bead Invisible Glow: 8.9 grams. The weight is light enough that it should not noticeably change the balance of a small EDC lanyard.
How to attach Gino to a paracord lanyard
The catalog describes Gino as a good addition to a black paracord knotted lanyard. The exact knot and cord diameter are up to you; the steps below cover the bead itself, not a specific knot pattern.
- Check your cord against the thru hole: The bead has a 1/4" (6.5mm) thru hole. Confirm your paracord or lanyard material fits through that opening before you commit to a knot.
- Decide which piece goes on first: Because Gino is a two-piece end stop, the head and the glow hat separate. Plan the order so the hat ends up hiding the cord end as intended.
- Thread the cord through the bead: Pass the lanyard material through the thru hole. The bead is an end stop, so it should sit at the end of the cord rather than slide freely along it.
- Thread the titanium head into the glow hat: The head threads into the hat. Hand-tighten only; the catalog does not specify a torque value, so do not force it.
- Check the finished end: Confirm the cord end is hidden inside the hat and the two pieces are seated together. If the cord does not fit the thru hole, stop and choose a different cord rather than forcing it.
How the glow works and what the catalog does not say
The glow comes from the hat, which the catalog describes as glow in the dark. Gino is available in three glow variants: Invisible Blue Glow, Invisible Green Glow, and Invisible Orange Glow. The color names refer to the hat's glow color, not to the titanium head.
The supplied information does not include a charging method, charge time, glow duration, or a recommended light source. That is a real limitation, not a hidden instruction. If you want a specific charging routine, ask the maker or check the packaging before relying on any method. What the catalog does confirm is that the glow component is the hat, so any charging approach would involve exposing that part to light.
Upkeep for a glow bead lanyard
The catalog does not supply cleaning agents, immersion guidance, or a service interval for Gino. The points below are practical handling notes based on the confirmed two-piece construction, not manufacturer instructions.
- Keep the threaded joint clean: Because the head threads into the hat, grit at that joint can make assembly feel rough. Wipe the threads before rethreading if the bead has been carried in a pocket.
- Do not overtighten: No torque specification is supplied. Hand-tight is the safe default; forcing the joint risks damaging the threads or the glow hat.
- Check the cord end periodically: The hat hides the end of the lanyard. If the cord works loose or the pieces separate, the end stop is no longer doing its job.
- Store it assembled or with both pieces together: A two-piece bead is easy to separate and misplace. Keeping the head and hat together protects the threaded interface and saves you a search.
Choosing a glow color for daily carry
The three variants differ by glow color, not by size or material. All share the same titanium head, the same 1/4" (6.5mm) thru hole, the same 13/16" (21mm) height, the same 7/8" (22mm) diameter, and the same 8.9-gram weight. If you are matching an existing lanyard or a bag color, the glow color is the only variable the catalog gives you.
The catalog also notes the black paracord knotted lanyard as a good pairing. That is a suggestion, not a requirement; any cord that fits the thru hole is a candidate, but the black paracord is the combination the listing calls out.
Gino at a glance
- Gino the Bead Invisible Glow: Available in Invisible Blue Glow, Invisible Green Glow, and Invisible Orange Glow. The glow color is the main choice between variants; dimensions and materials are shared.
- Gino the Bead Invisible Glow: Catalog price USD 37.50, with a catalog comparison price of USD 75.00. Price is listed for reference; confirm current pricing at checkout.


