Sideswipe Gen 2 Bolt and Pocket Clip: Fitting Your EDC Pen
By FocusWorks EDC | Published: 2026-11-03
Category: Panduan Cara
Step-by-step guide to swapping the bolt and pocket clip on your Sideswipe Gen 2 pen, with fit notes for Gen 1 compatibility and the tools you need.
Quick answer
To fit a new bolt or pocket clip on your Sideswipe Gen 2, you need a T6 Torx wrench and a clean, well-lit workspace. The process is straightforward, but Gen 1 pens require extra attention because the Gen 2 bolt will stick out more.
Gen 1 vs Gen 2 compatibility: what actually changes
The Sideswipe Gen 2 pocket clip is designed for Gen 2 pens and also fits Gen 1 pens without modification. The Gen 2 bolt is primarily for Gen 2 pens; it is compatible with Gen 1, but the bolt will protrude further. That extra stick-out is a functional difference, not a defect, so decide whether the added length bothers you before swapping.
If you are upgrading a Gen 1 pen, you can use both parts, but the bolt’s extra protrusion may affect how the pen sits in a pocket or pouch. The clip, by contrast, is a direct fit on both generations.
Tools and workspace: what you need before you start
A T6 Torx wrench is required for both the bolt and clip swap. Work over a tray or a light-colored cloth so small screws and the bolt don’t roll away. Avoid using a worn or oversized Torx driver, which can strip the screw head.
No other special tools are listed in the product information. If you don’t already own a T6 Torx wrench, confirm you have one before disassembly; it is not included with either part.
Step-by-step fitting process
- Prepare your workspace: Clear a flat, well-lit surface and place a tray or cloth underneath to catch small parts. Have your T6 Torx wrench within reach. A contained workspace prevents lost screws and bolts.
- Remove the existing pocket clip: Use the T6 Torx wrench to loosen the screw holding the clip. Support the pen body as you unscrew so the clip doesn’t spring away. Keep the screw with the old clip; you will reuse it unless a new one is supplied.
- Remove the existing bolt: Unscrew the bolt using the same T6 Torx wrench. Pay attention to any washers or spacers and note their order. Lay parts out in the order they came off to simplify reassembly.
- Install the new bolt: Thread the new bolt into the pen body by hand first, then snug it with the T6 Torx wrench. Do not overtighten; stop when the bolt sits flush or at the intended depth. On a Gen 1 pen, the Gen 2 bolt will stick out more—check that the extra length doesn’t interfere with your grip or carry method.
- Attach the new pocket clip: Position the clip over the mounting hole, insert the screw, and tighten with the T6 Torx wrench until the clip is secure but still allows slight flex. Test clip tension by sliding it over a pocket edge; adjust the screw if it feels too tight or too loose.
- Function check: Cycle the bolt action several times and clip the pen to a pocket or pouch. Confirm the bolt moves smoothly and the clip holds securely without scratching. If the bolt binds, loosen it a quarter turn; if the clip shifts, tighten the screw slightly.
Product facts
- Sideswipe Gen 2 Pocket clip: The Sideswipe Gen 2 pocket clip is precision-made from titanium and comes in Stonewashed, Satin, or Bead Blasted finishes. Titanium gives the clip durability for daily carry, and the finish options let you match the clip to your pen’s existing look.
- Gen 2 Bolt for SideSwipe Pen's: The Gen 2 bolt is compatible with Gen 1 pens but will cause extra stick-out. If you are fitting this bolt to a Gen 1 pen, expect a longer bolt profile that may change how the pen carries.
Gen 2 Bolt for SideSwipe Pen's
